netlink(7) — Linux manual pages

Linux manual pages	Section 7

Name

netlink — communication between kernel and user space (AF_NETLINK)

Synopsis

#include <asm/types.h>
#include <sys/socket.h>
#include <linux/netlink.h>

`netlink_socket = socket(`	`AF_NETLINK`,
	`socket_type`,
	`netlink_family)`;

DESCRIPTION

Netlink is used to transfer information between the kernel and user-space processes. It consists of a standard sockets-based interface for user space processes and an internal kernel API for kernel modules. The internal kernel interface is not documented in this manual page. There is also an obsolete netlink interface via netlink character devices; this interface is not documented here and is provided only for backward compatibility.

Netlink is a datagram-oriented service. Both SOCK_RAW and SOCK_DGRAM are valid values for socket_type. However, the netlink protocol does not distinguish between datagram and raw sockets.

netlink_family selects the kernel module or netlink group to communicate with. The currently assigned netlink families are:

NETLINK_ROUTE: Receives routing and link updates and may be used to modify the routing tables (both IPv4 and IPv6), IP addresses, link parameters, neighbor setups, queueing disciplines, traffic classes and packet classifiers (see rtnetlink(7)).
NETLINK_W1 (since Linux 2.6.13): Messages from 1-wire subsystem.
NETLINK_USERSOCK: Reserved for user-mode socket protocols.
NETLINK_FIREWALL: Transport IPv4 packets from netfilter to user space. Used by ip_queue kernel module.
NETLINK_INET_DIAG (since Linux 2.6.14): INET socket monitoring.
NETLINK_NFLOG: Netfilter/iptables ULOG.
NETLINK_XFRM: IPsec.
NETLINK_SELINUX (since Linux 2.6.4): SELinux event notifications.
NETLINK_ISCSI (since Linux 2.6.15): Open-iSCSI.
NETLINK_AUDIT (since Linux 2.6.6): Auditing.
NETLINK_FIB_LOOKUP (since Linux 2.6.13): Access to FIB lookup from user space.
NETLINK_CONNECTOR (since Linux 2.6.14): Kernel connector. See Documentation/connector/* in the Linux kernel source tree for further information.
NETLINK_NETFILTER (since Linux 2.6.14): Netfilter subsystem.
NETLINK_IP6_FW: Transport IPv6 packets from netfilter to user space. Used by ip6_queue kernel module.
NETLINK_DNRTMSG: DECnet routing messages.
NETLINK_KOBJECT_UEVENT (since Linux 2.6.10): Kernel messages to user space.
NETLINK_GENERIC (since Linux 2.6.15): Generic netlink family for simplified netlink usage.
NETLINK_CRYPTO (since Linux 3.2): Netlink interface to request information about ciphers registered with the kernel crypto API as well as allow configuration of the kernel crypto API.

Netlink messages consist of a byte stream with one or multiple nlmsghdr headers and associated payload. The byte stream should be accessed only with the standard NLMSG_* macros. See netlink(3) for further information.

In multipart messages (multiple nlmsghdr headers with associated payload in one byte stream) the first and all following headers have the NLM_F_MULTI flag set, except for the last header which has the type NLMSG_DONE.

After each nlmsghdr the payload follows.

struct nlmsghdr {

__u32 nlmsg_len;
/* Length of message including header */

__u16 nlmsg_type;
/* Type of message content */

__u16 nlmsg_flags;
/* Additional flags */

__u32 nlmsg_seq;
/* Sequence number */

__u32 nlmsg_pid;
/* Sender port ID */

};

nlmsg_type can be one of the standard message types: NLMSG_NOOP message is to be ignored, NLMSG_ERROR message signals an error and the payload contains an nlmsgerr structure, NLMSG_DONE message terminates a multipart message.

struct nlmsgerr {

int error;
/* Negative errno or 0 for acknowledgements */

struct nlmsghdr msg;
/* Message header that caused the error */

};

A netlink family usually specifies more message types, see the appropriate manual pages for that, for example, rtnetlink(7) for NETLINK_ROUTE.

Standard flag bits in `nlmsg_flags`
`NLM_F_REQUEST`	Must be set on all request messages.
`NLM_F_MULTI`	The message is part of a multipart message terminated by `NLMSG_DONE`.
`NLM_F_ACK`	Request for an acknowledgment on success.
`NLM_F_ECHO`	Echo this request.

Additional flag bits for GET requests
`NLM_F_ROOT`	Return the complete table instead of a single entry.
`NLM_F_MATCH`	Return all entries matching criteria passed in message content. Not implemented yet.
`NLM_F_ATOMIC`	Return an atomic snapshot of the table.
`NLM_F_DUMP`	Convenience macro; equivalent to (NLM_F_ROOT\|NLM_F_MATCH).

Note that NLM_F_ATOMIC requires the CAP_NET_ADMIN capability or an effective UID of 0.

Additional flag bits for NEW requests
`NLM_F_REPLACE`	Replace existing matching object.
`NLM_F_EXCL`	Don't replace if the object already exists.
`NLM_F_CREATE`	Create object if it doesn't already exist.
`NLM_F_APPEND`	Add to the end of the object list.

nlmsg_seq and nlmsg_pid are used to track messages. nlmsg_pid shows the origin of the message. Note that there isn't a 1:1 relationship between nlmsg_pid and the PID of the process if the message originated from a netlink socket. See the ADDRESS FORMATS section for further information.

Both nlmsg_seq and nlmsg_pid are opaque to netlink core.

Netlink is not a reliable protocol. It tries its best to deliver a message to its destination(s), but may drop messages when an out-of-memory condition or other error occurs. For reliable transfer the sender can request an acknowledgement from the receiver by setting the NLM_F_ACK flag. An acknowledgment is an NLMSG_ERROR packet with the error field set to 0. The application must generate acknowledgements for received messages itself. The kernel tries to send an NLMSG_ERROR message for every failed packet. A user process should follow this convention too.

However, reliable transmissions from kernel to user are impossible in any case. The kernel can't send a netlink message if the socket buffer is full: the message will be dropped and the kernel and the user-space process will no longer have the same view of kernel state. It is up to the application to detect when this happens (via the ENOBUFS error returned by recvmsg(2)) and resynchronize.

Address formats

The sockaddr_nl structure describes a netlink client in user space or in the kernel. A sockaddr_nl can be either unicast (only sent to one peer) or sent to netlink multicast groups (nl_groups not equal 0).

struct sockaddr_nl {

sa_family_t nl_family;
/* AF_NETLINK */

unsigned short nl_pad;
/* Zero */

pid_t nl_pid;
/* Port ID */

__u32 nl_groups;
/* Multicast groups mask */

};

nl_pid is the unicast address of netlink socket. It's always 0 if the destination is in the kernel. For a user-space process, nl_pid is usually the PID of the process owning the destination socket. However, nl_pid identifies a netlink socket, not a process. If a process owns several netlink sockets, then nl_pid can be equal to the process ID only for at most one socket. There are two ways to assign nl_pid to a netlink socket. If the application sets nl_pid before calling bind(2), then it is up to the application to make sure that nl_pid is unique. If the application sets it to 0, the kernel takes care of assigning it. The kernel assigns the process ID to the first netlink socket the process opens and assigns a unique nl_pid to every netlink socket that the process subsequently creates.

nl_groups is a bit mask with every bit representing a netlink group number. Each netlink family has a set of 32 multicast groups. When bind(2) is called on the socket, the nl_groups field in the sockaddr_nl should be set to a bit mask of the groups which it wishes to listen to. The default value for this field is zero which means that no multicasts will be received. A socket may multicast messages to any of the multicast groups by setting nl_groups to a bit mask of the groups it wishes to send to when it calls sendmsg(2) or does a connect(2). Only processes with an effective UID of 0 or the CAP_NET_ADMIN capability may send or listen to a netlink multicast group. Since Linux 2.6.13, messages can't be broadcast to multiple groups. Any replies to a message received for a multicast group should be sent back to the sending PID and the multicast group. Some Linux kernel subsystems may additionally allow other users to send and/or receive messages. As at Linux 3.0, the NETLINK_KOBJECT_UEVENT, NETLINK_GENERIC, NETLINK_ROUTE, and NETLINK_SELINUX groups allow other users to receive messages. No groups allow other users to send messages.

Socket options

To set or get a netlink socket option, call getsockopt(2) to read or setsockopt(2) to write the option with the option level argument set to SOL_NETLINK. Unless otherwise noted, optval is a pointer to an int.

NETLINK_PKTINFO (since Linux 2.6.14): Enable nl_pktinfo control messages for received packets to get the extended destination group number.
NETLINK_ADD_MEMBERSHIP, NETLINK_DROP_MEMBERSHIP (since Linux 2.6.14): Join/leave a group specified by optval.
NETLINK_LIST_MEMBERSHIPS (since Linux 4.2): Retrieve all groups a socket is a member of. optval is a pointer to __u32 and optlen is the size of the array. The array is filled with the full membership set of the socket, and the required array size is returned in optlen.
NETLINK_BROADCAST_ERROR (since Linux 2.6.30): When not set, netlink_broadcast() only reports ESRCH errors and silently ignore NOBUFS errors.
NETLINK_NO_ENOBUFS (since Linux 2.6.30): This flag can be used by unicast and broadcast listeners to avoid receiving ENOBUFS errors.
NETLINK_LISTEN_ALL_NSID (since Linux 4.2): When set, this socket will receive netlink notifications from all network namespaces that have an nsid assigned into the network namespace where the socket has been opened. The nsid is sent to user space via an ancillary data.
NETLINK_CAP_ACK (since Linux 4.2): The kernel may fail to allocate the necessary room for the acknowledgment message back to userspace. This option trims off the payload of the original netlink message. The netlink message header is still included, so the user can guess from the sequence number which message triggered the acknowledgment.

VERSIONS

The socket interface to netlink first appeared Linux 2.2.

Linux 2.0 supported a more primitive device-based netlink interface (which is still available as a compatibility option). This obsolete interface is not described here.

NOTES

It is often better to use netlink via libnetlink or libnl than via the low-level kernel interface.

BUGS

This manual page is not complete.

EXAMPLE

The following example creates a NETLINK_ROUTE netlink socket which will listen to the RTMGRP_LINK (network interface create/delete/up/down events) and RTMGRP_IPV4_IFADDR

struct sockaddr_nl sa;

memset(&sa, 0, sizeof(sa));
sa.nl_family = AF_NETLINK;
sa.nl_groups = RTMGRP_LINK | RTMGRP_IPV4_IFADDR;

fd = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
bind(fd, (struct sockaddr *) &sa, sizeof(sa));

The next example demonstrates how to send a netlink message to the kernel (pid 0). Note that the application must take care of message sequence numbers in order to reliably track acknowledgements.

struct nlmsghdr *nh;    /* The nlmsghdr with payload to send */
struct sockaddr_nl sa;
struct iovec iov = { nh, nh−>nlmsg_len };
struct msghdr msg;

msg = { &sa, sizeof(sa), &iov, 1, NULL, 0, 0 };
memset(&sa, 0, sizeof(sa));
sa.nl_family = AF_NETLINK;
nh−>nlmsg_pid = 0;
nh−>nlmsg_seq = ++sequence_number;
/* Request an ack from kernel by setting NLM_F_ACK */
nh−>nlmsg_flags |= NLM_F_ACK;

sendmsg(fd, &msg, 0);

And the last example is about reading netlink message.

int len;
char buf[4096];
struct iovec iov = { buf, sizeof(buf) };
struct sockaddr_nl sa;
struct msghdr msg;
struct nlmsghdr *nh;

msg = { &sa, sizeof(sa), &iov, 1, NULL, 0, 0 };
len = recvmsg(fd, &msg, 0);

for (nh = (struct nlmsghdr *) buf; NLMSG_OK (nh, len);
     nh = NLMSG_NEXT (nh, len)) {
    /* The end of multipart message */
    if (nh−>nlmsg_type == NLMSG_DONE)
        return;

    if (nh−>nlmsg_type == NLMSG_ERROR)
        /* Do some error handling */
    ...

    /* Continue with parsing payload */
    ...
}

COLOPHON

This page is part of release 4.07 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man−pages/.

t
This man page is Copyright (c) 1998 by Andi Kleen.

%%%LICENSE_START(GPL_NOVERSION_ONELINE)
Subject to the GPL.
%%%LICENSE_END

Based on the original comments from Alexey Kuznetsov
Modified 2005-12-27 by Hasso Tepper <hassoestpak.ee>
$Id: netlink.7,v 1.8 2000/06/22 13:23:00 ak Exp $

struct	nlmsghdr {
	__u32	`nlmsg_len`;	/* Length of message including header */
	__u16	`nlmsg_type`;	/* Type of message content */
	__u16	`nlmsg_flags`;	/* Additional flags */
	__u32	`nlmsg_seq`;	/* Sequence number */
	__u32	`nlmsg_pid`;	/* Sender port ID */
};

struct	nlmsgerr {
	int	`error`;	/* Negative errno or 0 for acknowledgements */
	struct nlmsghdr	`msg`;	/* Message header that caused the error */
};

struct	sockaddr_nl {
	sa_family_t	`nl_family`;	/* AF_NETLINK */
	unsigned short	`nl_pad`;	/* Zero */
	pid_t	`nl_pid`;	/* Port ID */
	__u32	`nl_groups`;	/* Multicast groups mask */
};