pipe — overview of pipes and FIFOs
Pipes and FIFOs (also known as named pipes) provide a unidirectional interprocess communication channel. A pipe has a read end and a write end. Data written to the write end of a pipe can be read from the read end of the pipe.
A pipe is created using pipe(2), which creates a new pipe and returns two file descriptors, one referring to the read end of the pipe, the other referring to the write end. Pipes can be used to create a communication channel between related processes; see pipe(2) for an example.
A FIFO (short for First In First Out) has a name within
the filesystem (created using mkfifo(3)), and is opened
using open(2). Any process may
open a FIFO, assuming the file permissions allow it. The read
end is opened using the O_RDONLY flag; the write end is opened
using the O_WRONLY flag. See
fifo(7) for further
details. Note:
although FIFOs have a pathname in the filesystem, I/O on
FIFOs does not involve operations on the underlying device
(if there is one).
The only difference between pipes and FIFOs is the manner in which they are created and opened. Once these tasks have been accomplished, I/O on pipes and FIFOs has exactly the same semantics.
If a process attempts to read from an empty pipe, then
read(2) will block until
data is available. If a process attempts to write to a full
pipe (see below), then write(2) blocks until
sufficient data has been read from the pipe to allow the
write to complete. Nonblocking I/O is possible by using the
fcntl(2) F_SETFL operation to enable the
O_NONBLOCK open file status
flag.
The communication channel provided by a pipe is a byte stream: there is no concept of message boundaries.
If all file descriptors referring to the write end of a
pipe have been closed, then an attempt to read(2) from the pipe
will see end-of-file (read(2) will return 0).
If all file descriptors referring to the read end of a pipe
have been closed, then a write(2) will cause a
SIGPIPE signal to be
generated for the calling process. If the calling process
is ignoring this signal, then write(2) fails with the
error EPIPE. An application
that uses pipe(2) and fork(2) should use
suitable close(2) calls to close
unnecessary duplicate file descriptors; this ensures that
end-of-file and SIGPIPE/EPIPE are delivered when
appropriate.
It is not possible to apply lseek(2) to a pipe.
A pipe has a limited capacity. If the pipe is full, then
a write(2) will block or
fail, depending on whether the O_NONBLOCK flag is set (see below).
Different implementations have different limits for the
pipe capacity. Applications should not rely on a particular
capacity: an application should be designed so that a
reading process consumes data as soon as it is available,
so that a writing process does not remain blocked.
In Linux versions before 2.6.11, the capacity of a pipe
was the same as the system page size (e.g., 4096 bytes on
i386). Since Linux 2.6.11, the pipe capacity is 65536
bytes. Since Linux 2.6.35, the default pipe capacity is
65536 bytes, but the capacity can be queried and set using
the fcntl(2) F_GETPIPE_SZ and F_SETPIPE_SZ operations. See fcntl(2) for more
information.
POSIX.1 says that write(2)s of less than
PIPE_BUF bytes must be
atomic: the output data is written to the pipe as a
contiguous sequence. Writes of more than PIPE_BUF bytes may be nonatomic: the
kernel may interleave the data with data written by other
processes. POSIX.1 requires PIPE_BUF to be at least 512 bytes. (On
Linux, PIPE_BUF is 4096
bytes.) The precise semantics depend on whether the file
descriptor is nonblocking (O_NONBLOCK), whether there are multiple
writers to the pipe, and on n, the number of bytes to
be written:
O_NONBLOCK disabled, n <= PIPE_BUFAll n
bytes are written atomically; write(2) may block
if there is not room for n bytes to be written
immediately
O_NONBLOCK enabled, n <= PIPE_BUFIf there is room to write n bytes to the pipe,
then write(2) succeeds
immediately, writing all n bytes; otherwise
write(2) fails,
with errno set to
EAGAIN.
O_NONBLOCK disabled, n > PIPE_BUFThe write is nonatomic: the data given to
write(2) may be
interleaved with write(2)s by other
process; the write(2) blocks
until n
bytes have been written.
O_NONBLOCK enabled, n > PIPE_BUFIf the pipe is full, then write(2) fails,
with errno set to
EAGAIN. Otherwise,
from 1 to n
bytes may be written (i.e., a "partial write" may
occur; the caller should check the return value from
write(2) to see how
many bytes were actually written), and these bytes
may be interleaved with writes by other
processes.
The only open file status flags that can be meaningfully
applied to a pipe or FIFO are O_NONBLOCK and O_ASYNC.
Setting the O_ASYNC flag
for the read end of a pipe causes a signal (SIGIO by default) to be generated when
new input becomes available on the pipe. The target for
delivery of signals must be set using the fcntl(2) F_SETOWN command. On Linux, O_ASYNC is supported for pipes and FIFOs
only since kernel 2.6.
mkfifo(1), dup(2), fcntl(2), open(2), pipe(2), poll(2), select(2), socketpair(2), splice(2), stat(2), mkfifo(3), epoll(7), fifo(7)
This page is part of release 4.07 of the Linux man-pages project. A
description of the project, information about reporting bugs,
and the latest version of this page, can be found at
https://www.kernel.org/doc/man−pages/.
|
Copyright (C) 2005 Michael Kerrisk <mtk.manpagesgmail.com> %%%LICENSE_START(VERBATIM) Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all copies. Permission is granted to copy and distribute modified versions of this manual under the conditions for verbatim copying, provided that the entire resulting derived work is distributed under the terms of a permission notice identical to this one. Since the Linux kernel and libraries are constantly changing, this manual page may be incorrect or out-of-date. The author(s) assume no responsibility for errors or omissions, or for damages resulting from the use of the information contained herein. The author(s) may not have taken the same level of care in the production of this manual, which is licensed free of charge, as they might when working professionally. Formatted or processed versions of this manual, if unaccompanied by the source, must acknowledge the copyright and authors of this work. %%%LICENSE_END |