Symbolic link ownership, permissions, and timestamps

The owner and group of an existing symbolic link can be changed using lchown(2). The only time that the ownership of a symbolic link matters is when the link is being removed or renamed in a directory that has the sticky bit set (see stat(2)).

The last access and last modification timestamps of a symbolic link can be changed using utimensat(2) or lutimes(3).

On Linux, the permissions of a symbolic link are not used in any operations; the permissions are always 0777 (read, write, and execute for all user categories), and can't be changed. (Note that there are some "magic" symbolic links in the /proc directory tree—for example, the /proc/PID/fd/* files—that have different permissions.)

Obtaining a file descriptor that refers to a symbolic link

Using the combination of the O_PATH and O_NOFOLLOW flags to open(2) yields a file descriptor that can be passed as the dirfd argument in system calls such as fstatat(2), fchownat(2), fchmodat(2), linkat(2), and readlinkat(2), in order to operate on the symbolic link itself (rather than the file to which it refers).

By default (i.e., if the AT_SYMLINK_FOLLOW flag is not specified), if name_to_handle_at(2) is applied to a symbolic link, it yields a handle for the symbolic link (rather than the file to which it refers). One can then obtain a file descriptor for the symbolic link (rather than the file to which it refers) by specifying the O_PATH flag in a subsequent call to open_by_handle_at(2). Again, that file descriptor can be used in the aforementioned system calls to operate on the symbolic link itself.

Handling of symbolic links by system calls and commands

Symbolic links are handled either by operating on the link itself, or by operating on the object referred to by the link. In the latter case, an application or system call is said to follow the link. Symbolic links may refer to other symbolic links, in which case the links are dereferenced until an object that is not a symbolic link is found, a symbolic link that refers to a file which does not exist is found, or a loop is detected. (Loop detection is done by placing an upper limit on the number of links that may be followed, and an error results if this limit is exceeded.)

There are three separate areas that need to be discussed. They are as follows:

System calls

The first area is symbolic links used as filename arguments for system calls.

Except as noted below, all system calls follow symbolic links. For example, if there were a symbolic link slink which pointed to a file named afile, the system call open("slink" ...) would return a file descriptor referring to the file afile.

Various system calls do not follow links, and operate on the symbolic link itself. They are: lchown(2), lgetxattr(2), llistxattr(2), lremovexattr(2), lsetxattr(2), lstat(2), readlink(2), rename(2), rmdir(2), and unlink(2).

Certain other system calls optionally follow symbolic links. They are: faccessat(2), fchownat(2), fstatat(2), linkat(2), name_to_handle_at(2), open(2), openat(2), open_by_handle_at(2), and utimensat(2); see their manual pages for details. Because remove(3) is an alias for unlink(2), that library function also does not follow symbolic links. When rmdir(2) is applied to a symbolic link, it fails with the error ENOTDIR.

link(2) warrants special discussion. POSIX.1-2001 specifies that link(2) should dereference oldpath if it is a symbolic link. However, Linux does not do this. (By default, Solaris is the same, but the POSIX.1-2001 specified behavior can be obtained with suitable compiler options.) POSIX.1-2008 changed the specification to allow either behavior in an implementation.

Commands not traversing a file tree

The second area is symbolic links, specified as command-line filename arguments, to commands which are not traversing a file tree.

Except as noted below, commands follow symbolic links named as command-line arguments. For example, if there were a symbolic link slink which pointed to a file named afile, the command cat slink would display the contents of the file afile.

It is important to realize that this rule includes commands which may optionally traverse file trees; for example, the command chown file is included in this rule, while the command chown −R file, which performs a tree traversal, is not. (The latter is described in the third area, below.)

If it is explicitly intended that the command operate on the symbolic link instead of following the symbolic link—for example, it is desired that chown slink change the ownership of the file that slink is, whether it is a symbolic link or not—the −h option should be used. In the above example, chown root slink would change the ownership of the file referred to by slink, while chown −h root slink would change the ownership of slink itself.

There are some exceptions to this rule:

Commands traversing a file tree

The following commands either optionally or always traverse file trees: chgrp(1), chmod(1), chown(1), cp(1), du(1), find(1), ls(1), pax(1), rm(1), and tar(1).

It is important to realize that the following rules apply equally to symbolic links encountered during the file tree traversal and symbolic links listed as command-line arguments.

The first rule applies to symbolic links that reference files other than directories. Operations that apply to symbolic links are performed on the links themselves, but otherwise the links are ignored.

The command rm −r slink directory will remove slink, as well as any symbolic links encountered in the tree traversal of directory, because symbolic links may be removed. In no case will rm(1) affect the file referred to by slink.

The second rule applies to symbolic links that refer to directories. Symbolic links that refer to directories are never followed by default. This is often referred to as a "physical" walk, as opposed to a "logical" walk (where symbolic links that refer to directories are followed).

Certain conventions are (should be) followed as consistently as possible by commands that perform file tree walks:

For commands that do not by default do file tree traversals, the −H, −L, and −P flags are ignored if the −R flag is not also specified. In addition, you may specify the −H, −L, and −P options more than once; the last one specified determines the command's behavior. This is intended to permit you to alias commands to behave one way or the other, and then override that behavior on the command line.

The ls(1) and rm(1) commands have exceptions to these rules: